Aristel IPX-100 Installation Manual Download Page 27

Page: 27 / 114

IPX-100 system installation & configuration

Page-27

TELECOMMUNICATIONS

2-4-2

FXO(trunk) Port Settings

Ring On Time

To set the maximum of ring on signal recognized time.

Ring Off Time

To set the maximum of ring off (interval silence) recognized time.

Caller ID Waiting Time

To set the caller ID signal waiting time from central office (PSTN).

Tx Gain

Transmission gain value, from -9dB~+4dB.

Rx Gain

Receiption gain value, from -9dB~+4dB.

2-4-3

FXS(SLT) Port Settings

Max. Flash Time

The maximum flash time to place the call on hold. Otherwise, the call will be

hung up if the flash time is longer than the maximum flash time range.

Min. Flash Time

The minimum flash time to place the call on hold. the flash will be ignored

(not to place the call on hold) if the flash time is shorter than the minimum

flash time range.

Tx Gain

Transmission gain value, from -30dB~+6dB

Rx Gain

Receiption gain value, from -30dB~+6dB

Caller ID Mode

DTMF

Use the ETSI protocol to transmit caller messages with DTMF signals

FSK

Use the UAE protocol to transmit caller messages with FSK signals

FSK Pre-ring Time

Ringing time for pre-sending ringing before transmitting FSK signal.

Summary of Contents for IPX-100



















































































































Search results

Summary of Contents for IPX-100

Reviews:

Related manuals for IPX-100

Brands by name

Popular brands

Aristel IPX-100, Installation Manual

Search results

Summary of Contents for IPX-100

Reviews:

Related manuals for IPX-100

Brands by name

Popular brands