Aristel IPX-100 Installation Manual Download Page 44

Page: 44 / 114

IPX-100 system installation & configuration

Page-44

TELECOMMUNICATIONS

3-6

TOS/COS

At this page to set the basic operating parameters of packet traffic when the system transmits
packets as below

：

ToS for SIP packets

Set the ToS setting value of the SIP packet (default is cs3).

ToS for RTP audio packets

Set the ToS setting of the voice packet (default is ef).

ToS for RTP video packets

Set the ToS setting of the image packet (default is af41).

ToS for RTP text packets

Set the ToS setting of the text message packet (default is af41).

、

cs0~7

、

af11~41 The Codepoint name indicates the DSCP

value of 6 bits. For the priority level,
please refer to Appendix 6. The higher the
value, the higher the priority.

CoS for SIP packets

Set the 802.1p level of the SIP packet (default is 3).

CoS for RTP audio packets

Set the 802.1p level of the voice packet (default is 5).

CoS for RTP video packets

Set the 802.1p level of the image packet (default is 4).

CoS for RTP text packets

Set the 802.1p level of the text message packet (default is 3).

0~7

Since 802.1p uses 3 bits to represent the VLAN header,
the level is 7 levels, 0 is the lowest, and 7 is the highest.

3-7

Auth & SIP Packet

At this page to set the basic operating parameters used by the PBX core to process SIP packets
and verification as below

：

Always Reject Un-authenticate Peer

Whether to reject all unverified INVITE or
REGISTER requests until they are verified.

Always allow.

Yes Always reject (system default).

This is a way to effectively prevent hackers
from scanning attacks. Please note that if
there is no other way to help prevent
hacker scanning attacks, please do not turn
off this feature.

Summary of Contents for IPX-100



















































































































Search results

Summary of Contents for IPX-100

Reviews:

Related manuals for IPX-100

Brands by name

Popular brands

Aristel IPX-100, Installation Manual

Search results

Summary of Contents for IPX-100

Reviews:

Related manuals for IPX-100

Brands by name

Popular brands