Aristel IPX-100 Installation Manual Download Page 87

Page: 87 / 114

IPX-100 system installation & configuration

Page-87

TELECOMMUNICATIONS

5-9-1-2

Options

At this page sets the working parameters of the incoming route, description as below :

Strip No

Strip the number of the prefix code of the incoming call number (for

example, set to 2, the incoming line number 0285123000, and the

number after deletion is 85123000).

Add Prefix

To add the prefix number in front of incoming call number.

Maximum Channels Allows the number of calls that can be entered at the same line

number at the same time.

Alert Info

Prompt message, message for the call request packet added to the

SIP phone.

5-9-1-3

Destination

The main items selected in the destination options are Hangup, Voicemail, Extension, and

Forward To. According to the user settings, the selectable items are IVR, Ring Group, Queue,

Time Condition, and Conference Room. described as follows

：

Hangup

Hangup the call

Voicemail

Forward to voicemail, “Dialed Ext.” to enabled voicemail forward

function code for the extension.

IVR

Forward to IVR.

Ring Group

Forward to ring group.

Extension

Forward to extension.

Queue

Forward on queue.

Time Condition

Set processing according to time conditions.

Conference Room

Forward to tele-conference room.

Forward To

Forward to trunk line (set trunk line route code + outgoing number).

Summary of Contents for IPX-100



















































































































Search results

Summary of Contents for IPX-100

Reviews:

Related manuals for IPX-100

Brands by name

Popular brands

Aristel IPX-100, Installation Manual

Search results

Summary of Contents for IPX-100

Reviews:

Related manuals for IPX-100

Brands by name

Popular brands