Aristel IPX-100 Installation Manual Download Page 58

Page: 58 / 114

IPX-100 system installation & configuration

Page-58

TELECOMMUNICATIONS

4-2-1-3

Technology

At this page to set parameters for the communication protocol of this SIP phone as below

：

Active Service

Yes

Enabled, users can answer or make calls using the phone

connected to this port.

Disabled this port.

Type

phone set working type.

SIP

SIP extension of this cabinet.

Remote IPX-100

SIP extension of other remote cabinets (string cabinets).

DTMF Mode

The transmission mode used to transmit DTMF signals, the options are as

follows

：

Auto

system auto selection.

RFC2833

Transmit DTMF message packets using the RFC2833 protocol.

SIP Info

Transfer DTMF message packets using SIP Info.

Inband

Transmission of DTMF signals by voice channel.

Audio Codec

G.729

G.729 Compression format.

G.723

G.723 Compression format.

G.711-ulaw G.711 ulaw Coding format (US).

G.711-alaw G.711 alaw Coding format (EU).

G.711

G.711format

，

a/ulaw.

ALL

All coding format can be determined by the setting of the phone

itself.

Video Codec

No Used

Video call not allowed.

H.263

H.263 Compression format.

H.264

H.264 Compression format.

Note:

The system only provides the packet transmition function. The video

codec is completed by both parties. Please be sure to select the correct codec

when setting the phone.

Summary of Contents for IPX-100



















































































































Search results

Summary of Contents for IPX-100

Reviews:

Related manuals for IPX-100

Brands by name

Popular brands

Aristel IPX-100, Installation Manual

Search results

Summary of Contents for IPX-100

Reviews:

Related manuals for IPX-100

Brands by name

Popular brands