Commissioning Test and Record Sheet
P12y/EN RS/D32
MiCOM P125/P126 & P127
Page 7/48
Below it is listed the guide table.
Type and setting current stage
in Ien, Ue> in Volt, in degrees for
the torque angle and the trip zone
Value
applied in In,
in Volt and
the angles in
degrees
Delay Time
Setting
Measured
Trip Delay
time
Drop value for
Ien, Ue,
Torque angle,
and trip zone
Ie>:
0.5 x Ie>
Ue>:10V
2 x 10V
Torque angle : 0°
0°
Trip Zone : +/- 90°
+/-85°
1s
Type and setting current stage
in Ien, the Ue> in Volt and in
degrees the torque angle and the
trip zone
Value
applied in In,
in Volt and
the angles in
degrees
Delay Time
Setting
Measured
Trip Delay
time
Drop value for
Ien, Ue,
Torque angle,
and trip zone
Ie>:
2 x Ie>
Ue>:10V
80V
Torque angle : 0°
0°
Trip Zone : +/- 90°
+/-85°
1s
1.10
Earth Fault Wattmetric protection test
The earth fault wattmetric protection can be tested but as above needs of the residual
voltage injection the wattmetric power is calculated as Ie x Ue x cos (Ie^Ue+
ϕ
c)
The calculation is referred to the secondary values.
The same test can be repeated for the second stage.
Type and setting Pe stage are in
watt referred to the secondary.
The setting value depends on the
set nominal Ien current (1A).
Value
applied in In,
in Volt and
the angles in
degrees
Delay Time
Setting
Measured
Trip Delay
time
Drop value for
Ien, Ue,
Torque angle,
and trip zone
0.5 x
Ien=0.5A
Ue=45V
Pe>: 20W
Ue^Ie =0°
ϕ
c = 0°
tPe>=1s
Note: Change the angle between Ue^Ie and verify the trip and drop off of the Pe stage and
the value of the Pe in the measurement menu.
Summary of Contents for MiCOM P125
