P12y/EN FT/D32
User Guide
Page 4/86
MiCOM P125/P126 & P127
2. PASSWORD
2.1 Password
Protection
Password protection is applicable to most of the relay settings, especially to the selection of
the various alarm thresholds, trip thresholds, communication parameters, allocation of logic
inputs and outputs.
The password consists of four capital characters. When leaving the factory, the password is
set to AAAA. The user can define any combination of four characters.
Should the password be lost or forgotten, modification of the stored parameters is blocked. It
is then necessary to contact the manufacturer or his agent and a stand-by password specific
to the relay concerned may be obtained.
The programming mode is indicated with the letter "P" on the right hand side of the display
on each menu heading. The letter "P" remains present as long as the password is active
(5 minutes if there is no action on the keypad).
2.2 Password
Entry
The input of the password is requested as soon as a modification of a parameter is made for
any one of the six/eight menus and the submenus. The user enters each of the 4 characters
and then validates the entire password with
%
.
After 5 seconds, the display returns to the point of the preceding menu.
If no key is pressed inside of 5 minutes, the password is deactivated. A new password
request is associated with any subsequent parameter modification.
2.3
Changing the Password
To change an active password, go to the OP. PARAMETERS menu and then to the
Password submenu. Enter the current password and validate. Then press
%
and enter the
new password character by character and validate the new password using
%
.
The message NEW PASSWORD OK is displayed to indicate that the new password has
been accepted.
2.4
Change of Setting Invalidation
The procedure to modify a setting is shown in the next part of this document.
If during this action it occurs the need to get back to the old setting it is necessary push the
&
key
before validating the setting change
. After this action the following message will
appear on the LCD for some seconds and the old setting will be maintained.
UPGRADE
CANCEL
2.5
Displays of Alarm & Warning Messages
Alarm messages are displayed directly on the front panel LCD. They have priority over the
default current value. As soon as an alarm situation is detected by the relay (threshold
crossing for example), the associated message is displayed on the MiCOM relay front panel
LCD and the LED Alarm (LED 2) lights up.
The alarm and warning messages are classed as follows:
Alarm messages generated by the electrical power network.
Warning messages caused by hardware or software faults from the relay.
Summary of Contents for MiCOM P125
