manualshive.com logo in svg

APRILIA TUAREG 660, Service Station Manual

Share
Download
APRILIA TUAREG 660 Service Station Manual Download Page 36

Scheduled maintenance table

NOTE

THE MAINTENANCE INTERVALS PRESCRIBED BY THE SCHEDULED MAINTENANCE TABLE
MUST BE CONSIDERED AS A GENERAL GUIDE FOR USING THE VEHICLE IN NORMAL RUN-
NING CONDITIONS.
IT MAY BE NECESSARY TO REDUCE THE MAINTENANCE INTERVALS UNDER SOME PARTIC-
ULAR CONDITIONS. ESPECIALLY WHEN USED IN GEOGRAPHICAL LOCATIONS WITH AD-
VERSE CLIMATIC CONDITIONS, USE ON UNEVEN GROUND OR SEVERE INDIVIDUAL USE.

NOTE

THE TIMES LISTED ON THE SCHEDULED MAINTENANCE TABLE INCLUDE TIME DEDICATED
TO MANAGEMENT ACTIVITIES.

I: CHECK AND CLEAN, ADJUST, LUBRICATE OR REPLACE, IF NECESSARY

C: CLEAN, R: REPLACE, A: ADJUST, L: LUBRICATE

(1) Check and clean and adjust or replace, if necessary, before every journey.

(2) Check and clean, adjust or replace if necessary every 1,000 km (621.37 mi).

(3) Replace at whichever of the following occurs first: 40,000 km (24,854.85 mi) or 4 years.

(4) Maintenance interval halved in the event of off-road use.

SCHEDULED MAINTENANCE TABLE

km x 1,000 (mi x 1,000)

1 (0.6)

10

(6.2)

20

(12.4)

30

(18.6)

40

(24.9)

12

months

24

months

Rear shock absorber (bearings - linkage systems) (4)

I

I

I

I

Engine oil filler plug O-ring

I

I

I

I

I

I

I

Flywheel cover cap O-Ring

I

I

Fork plug O-ring

I

Motorcycle set up

I

I

I

I

I

Spark plug

R

R

Drive chain (2) (4)

I - L

I - L

I - L

I - L

I - L

I

I

Clutch cable (4)

L

L

L

L

L

L

L

Front sprocket - rear sprocket - Chain slider - chain ten-
sioner roller

I

I

I

I

Steering bearings and steering play

I

I

I

I

I

I

I

Wheel bearings - Wheels (4)

I

I

I

I

I

I

I

Diagnosis by tool

I

I

I

I

I

I

I

Brake discs - Brake pads wear (1)

I

I

I

I

I

I

I

Air filter (4)

I

R

I

R

Engine oil filter

R

R

R

R

R

R

R

Vehicle general operation

I

I

I

I

I

I

I

Valve clearance

A

A

Head cover gasket

I

I

Engine oil discharge plug aluminium gasket

R

R

R

R

R

R

R

Coolant drain screw aluminium gasket

R

Spark plug shanks gasket

R

R

Cooling system

I

I

I

I

Brake systems

I

I

I

I

I

I

I

Safety switches (stand, stop, clutch, extra negative stroke,
gas control)

I

I

I

I

I

I

I

Brake fluid

I

I

I

I

I

I

R

Coolant

I

I

I

I

I

I

R

Fork oil (3) (4)

R

Engine oil

R

R

R

R

R

R

R

Headlight aiming

I

I

I

I

Fork oil seals (4)

I

I

I

I

R

Tyres - pressure / wear (1)

I

I

I

I

I

I

I

Nut/bolt tightness (4)

I

I

I

I

I

Head cover fastening screws dampers

I

I

Maintenance

TUAREG 660

MAIN - 36

Summary of Contents for TUAREG 660
























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands