manualshive.com logo in svg

APRILIA TUAREG 660, Service Station Manual

Share
Download
APRILIA TUAREG 660 Service Station Manual Download Page 189

•

Tighten the rear wheel locking nut to

the prescribed torque.

•

Rotate the wheel a few times to check that it does not stick.

Swinging arm

Removing

Using straps, block the front part, position a scissor

lift centrally to keep the rear part raised when re-

moving the swingarm.

To proceed with the removal of the swingarm, it is

necessary to first remove the rear wheel, rear

mudguard and chain cover.

•

Then proceed with the removal of the

rear brake calliper complete with sup-

port by disconnecting the brake line

and the rear ABS sensor wiring har-

ness from the three cable guides on the

swingarm.

•

Position a rear stand to support the

swingarm and unscrew the nut (1) and

remove the screw (2) fixing the dual

linkage to the swingarm.

•

Then if necessary remove the bush (3).

TUAREG 660

Chassis

CHAS - 189

Summary of Contents for TUAREG 660
























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands