manualshive.com logo in svg

APRILIA TUAREG 660, Service Station Manual

Share
Download
APRILIA TUAREG 660 Service Station Manual Download Page 306

Radiator cover

To remove the radiator cover it is necessary to

firstly remove the side and lower fairings.

Unhook the hooks on the radiator cover and re-

move it.

Battery

To remove the battery, proceed as described:

•

Ensure that the ignition switch is turned

to "OFF".

•

Remove the saddle.

•

Undo the two screws (1) and remove

the battery cover (2).

•

Unscrew and remove the screw (3)

from the negative terminal (-).

•

Move the negative lead (4) aside.

•

Unscrew and remove the screw (5) of

the positive terminal (+).

•

Move the positive lead (6) aside.

TAKE UTMOST CAR AND DO NOT MAKE CONTACT BE-
TWEEN THE BATTERY TERMINALS AND ANY METALLIC
OBJECT IN ORDER TO PREVENT THE RISK OF SHORT
CIRCUIT.

Bodywork

TUAREG 660

BODYW - 306

Summary of Contents for TUAREG 660
























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands