manualshive.com logo in svg

APRILIA TUAREG 660, Service Station Manual

Share
Download
APRILIA TUAREG 660 Service Station Manual Download Page 149

•

Insert the safety plate (5).

Steering bearing

Adjusting play

To adjust the steering play, follow the procedure described below:

•

Place the vehicle so that the front wheel is off the ground.

•

Carry out a handlebar rotation test, using a dynamometer at the hand grip external end.

•

The handlebar resistance to rotation must be of 250 +/- 100 g (0.55 +/- 0.22 lb) in both

directions.

•

Adjust if clearance is detected.

NOTE

THE STEERING COLUMN RESISTANCE TO ROTATION MUST BE PERFORMED IN THE TWO
OPPOSITE ROTATION DIRECTIONS.

•

Remove the handlebars and upper

steering triple clamp.

Then proceed as described:

•

Remove the steering safety plate (1).

•

Remove the upper steering ring nut (2)

using the special tool.

Specific tooling

AP8140190

 

Steering tightening tool

TUAREG 660

Suspensions

SUSP - 149

Summary of Contents for TUAREG 660
























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands