manualshive.com logo in svg

APRILIA TUAREG 660, Service Station Manual

Share
Download
APRILIA TUAREG 660 Service Station Manual Download Page 155

•

Supporting the lower triple clamp, in-

sert the dust seal ring (8) on the head-

stock.

•

Supporting the lower triple clamp, in-

sert the rubber dust seal (9) on the

headstock.

•

Supporting the lower triple clamp, insert the ring nut (10) on the headstock and tighten it fully

by hand.

•

Using the special tool, pre-tighten the

ring nut to 60 Nm (44.25 lbf ft).

•

Turn the handlebar to the left and right

as far as it will go to seat the bearings.

•

Unscrew the ring nut and tighten it to a

torque of 40 +/- 5 Nm (29.50 +/- 3.68

lbf ft).

•

Rotate the steering yoke all the way to

the left and right to check that the ro-

tation is smooth and without jamming.

Specific tooling

AP8140190

 

Steering tightening tool

TUAREG 660

Suspensions

SUSP - 155

Summary of Contents for TUAREG 660
























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands