manualshive.com logo in svg

APRILIA TUAREG 660, Service Station Manual

Share
Download
APRILIA TUAREG 660 Service Station Manual Download Page 281

•

Disconnect the first connector of the

left switch cluster (6) from the guide on

the instrument panel support and dis-

connect it

•

Disconnect the second connector of

the left switch cluster (7).

•

Unscrew the fixing screw (8) of the right

switch cluster and slide it off the han-

dlebar to remove it.

USE NEW CLAMPS DURING REASSEMBLY.

Driving mirrors

Removing the rear-view mirrors:

•

Rest the vehicle on its stand.

•

Lift the rubber protection (1).

•

Loosen the fastening nut (2) by ensur-

ing that the threaded clamp (3) cannot

rotate.

•

Slide up and remove the complete

rear-view mirror unit (4).

Repeat the procedure to remove the other rear-

view mirror, if necessary.

UPON REFITTING AND BEFORE TIGHTENING THE LOCK-
ING NUT, MAKE SURE THAT THE REAR VIEW MIRROR
SUPPORT STEM IS ALIGNED WITH THE HANDLEBAR.

CAUTION

THE VEHICLE MAY NOT BE RIDDEN ON PUBLIC ROADS
WITH THE REAR VIEW MIRRORS REMOVED.

TUAREG 660

Bodywork

BODYW - 281

Summary of Contents for TUAREG 660
























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands