manualshive.com logo in svg

APRILIA TUAREG 660, Service Station Manual

Share
Download
APRILIA TUAREG 660 Service Station Manual Download Page 224

TO REACTIVATE, TURN THE IGNITION SWITCH OFF AND THEN ON AGAIN AND SELECT THE
REQUIRED SETTING.

NOTE

THE SAFETY PROVIDED BY THE ABS DOES NOT, IN ANY CASE, JUSTIFY RISKY MANOEU-
VRES. EVEN THOUGH THE ABS SYSTEM ENSURES GREATER VEHICLE CONTROL IN THE
EVENT OF EMERGENCY BRAKING, ALWAYS OBSERVE THE CORRECT MINIMUM SAFETY
DISTANCE FROM THE VEHICLE IN FRONT OF YOU.

THE ABS SYSTEM ACTS ON BOTH THE FRONT AND REAR WHEELS BY OBTAINING INFOR-
MATION FROM THE ROTATION/ LOCKING TONE WHEELS. ALWAYS CHECK THAT THE TONE
WHEEL IS CLEAN, AND REGULARLY CHECK THAT THE DISTANCE FROM THE SENSOR IS
CONSTANT ON ALL 360 DEGREES. SHOULD THE WHEELS BE REMOVED AND REFITTED, IT
IS VERY IMPORTANT TO CHECK THAT THE DISTANCE BETWEEN TONE WHEEL AND SENSOR
IS THE ONE SPECIFIED. FOR CHECKING AND ADJUSTMENT, CONTACT AN Authorised

 

Apri-

lia

 Workshop.

WHERE THE MOTORCYCLE HAS AN ABS SYSTEM, NON-APPROVED BRAKE PADS AND
TYRES COMPROMISE SMOOTH BRAKING, DRASTICALLY REDUCING DRIVING SAFETY.

NOTE

THE SYSTEM'S SENSORS, HAVING A SIGNIFICANT ACCURACY OF READING THE TONE
WHEELS, MAY GENERATE, A MOTORCYCLE STOPPED AND THE ENGINE RUNNING, INDICA-
TION OF SPEED OF SOME km / h (mph) ON THE DIGITAL DISPLAY.
SUCH BEHAVIOUR IS TO BE CONSIDERED NORMAL AND DOES NOT CREATE MALFUNC-
TIONS IN THE SYSTEM.

IF THE GAP FOR ONE OR BOTH SENSORS IS NOT WITHIN THE TOLERANCE INDICATED BE-
LOW, TAKE THE MOTORCYCLE TO AN Approved Aprilia Dealer

Characteristic

Distance between tone wheel and front sensor

0.5 - 2.00 mm (0.020 - 0.079 in)

Distance between tone wheel and the rear sensor

0.5 - 2.00 mm (0.020 - 0.079 in)

Braking system

TUAREG 660

BRAK SYS - 224

Summary of Contents for TUAREG 660
























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands