manualshive.com logo in svg

APRILIA TUAREG 660, Service Station Manual

Share
Download
APRILIA TUAREG 660 Service Station Manual Download Page 289

Side body panels

To disassemble the side panels it is necessary to

first remove the side tail fairings. Then proceed as

described:

The operations described refer to a side panel

but are valid for both

•

Remove the two screws with relative

washers and separate the side panel

from the side tail fairing.

Side fairings

To remove the side fairings, proceed as described:

THE FOLLOWING OPERATIONS REFER TO

ONE SIDE BUT ARE VALID FOR BOTH.

•

Remove the clip (1).

•

Remove the lateral fastener screw (2).

•

Remove the internal screw (3) that se-

cures the side fairing to the radiator.

TUAREG 660

Bodywork

BODYW - 289

Summary of Contents for TUAREG 660
























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands