APRILIA TUAREG 660 Service Station Manual Download Page 26

Page: 26 / 311

Specification

Desc./Quantity

Overspeed threshold/shift light

LED

Immobilizer

LED

Fuel reserve

LED

a-PRC

LED

General warning

LED

DRL

LED

Side stand

LED

Frame and suspensions

HASSIS

Specification

Desc./Quantity

Type

Welded tubular double cradle steel frame.

Steering rake angle

26.7° (measurements with respect to bare chassis)

USPENSION

Specification

Desc./Quantity

Front fork

Adjustable upside-down hydraulic fork with 43 mm (1.69 in)

stanchions

Front stroke

240 mm (9.44 in)

Rear shock absorber

Progressive linkage with piggy-back. Adjustable spring pre-

load, hydraulic compression and rebound damping.

Rear stroke

106,5 mm (4.19 in)

RAME

DIMENSIONS

Specification

Desc./Quantity

Size "A"

559.1 mm (22.01 in) (measurements refer to the bare chassis)

Size "B"

456.9 mm (17.98 in) (measurements refer to the bare chassis)

Angle "C"

26.7° +/- 0.25° (measurements refer to the "naked" frame)

Brakes

RAKES

Specification

Desc./Quantity

Front

Discs Ø 300 mm (11.81 in), two-piston floating callipers - Ø

30-32 mm (1.18-1.25 in) and 2 pads - axial pump with integra-

ted reservoir.

Rear

Disc brake - Ø 260 mm (10.23 in), single-piston floating calliper

- Ø 34 mm (1.34 in) - pump with separate reservoir.

Characteristics

TUAREG 660

CHAR - 26

Summary of Contents for TUAREG 660
























































































































































































































































































































Search results

Summary of Contents for TUAREG 660

Reviews:

Brands by name

Popular brands

APRILIA TUAREG 660, Service Station Manual

Search results

Summary of Contents for TUAREG 660

Reviews:

Brands by name

Popular brands