APRILIA TUAREG 660 Service Station Manual Download Page 177

Page: 177 / 311

REMOVAL OF INTERNAL WHEEL COMPO-

NENTS

To proceed with the removal of the internal wheel

components, proceed as described:

•

Working on the right side of the wheel,

remove the oil seal (19).

•

Using special pliers, remove the circlip

(20).

•

Using a generic puller, proceed with

the extraction of the bearing as descri-

bed:

•

Insert the first part of the tool (A) on the

bearing and screw the pin (B).

•

Insert the second part (C) and the nut

(D).

•

Tighten the nut while keeping the pin

(A) still, to extract the bearing.

TUAREG 660

Chassis

CHAS - 177

Summary of Contents for TUAREG 660
























































































































































































































































































































Search results

Summary of Contents for TUAREG 660

Reviews:

Brands by name

Popular brands

APRILIA TUAREG 660, Service Station Manual

Search results

Summary of Contents for TUAREG 660

Reviews:

Brands by name

Popular brands