APRILIA TUAREG 660 Service Station Manual Download Page 215

Page: 215 / 311

RH RIDER FOOTREST

To assemble and install the right rider footrest,

proceed as follows:

•

Position the rear brake switch on the

support plate and tighten the two

screws (1).

•

Insert the swingarm pin (2) into the

support plate (3) taking care to insert

the spacers (4) on both sides, checking

the correct orientation, as in the photo.

•

Insert the flat washer (5) and manually

screw the nut (6).

•

Insert the lower fixing screw (7) of the

plate to the frame and screw it man-

ually.

•

Then tighten the nut (6), swingarm pin

and then of the screw (7) to the pre-

scribed torque.

TUAREG 660

Chassis

CHAS - 215

Summary of Contents for TUAREG 660
























































































































































































































































































































Search results

Summary of Contents for TUAREG 660

Reviews:

Brands by name

Popular brands

APRILIA TUAREG 660, Service Station Manual

Search results

Summary of Contents for TUAREG 660

Reviews:

Brands by name

Popular brands