manualshive.com logo in svg

APRILIA TUAREG 660, Service Station Manual

Share
Download
APRILIA TUAREG 660 Service Station Manual Download Page 247

•

Remove the tone wheel (2) (if applica-

ble).

•

Remove the brake disc (3).

Disc Inspection

•

The following operations must be car-

ried out with the brake discs fitted on

the wheel; they refer to a single disc,

but are valid for both.

•

Check the disc for wear by measuring

the minimum thickness with a micro-

meter in different points. If the mini-

mum thickness, even in a single point

of the disc, is less than the minimum

value, replace the disc.

Disc thickness minimum value: 4 mm (0.16 in)

•

Using a dial gauge, check that the max-

imum oscillation of the disc does not

exceed the tolerance; otherwise, re-

place it.

Disc oscillation tolerance: 0.15 mm (0.0059 in)

TUAREG 660

Braking system

BRAK SYS - 247

Summary of Contents for TUAREG 660
























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands