APRILIA TUAREG 660 Service Station Manual Download Page 208

Page: 208 / 311

RH RIDER FOOTREST

To disassemble and remove the right rider footrest

it is necessary to first remove the frame protection.

Then proceed as described:

•

Unscrew the two fixing screws (1) of

the rear brake master cylinder (2).

•

Release the brake lever return spring

(3) and remove it.

•

Unscrew the fixing screw (4) of the

brake lever (5) taking care to retain the

two rubber o-rings (6) and the washer

(7).

•

Remove the split pin (6) of the pin and

the washer (7).

CAUTION

ALWAYS USE A NEW SLIT PIN DURING REASSEMBLY .

Chassis

TUAREG 660

CHAS - 208

Summary of Contents for TUAREG 660
























































































































































































































































































































Search results

Summary of Contents for TUAREG 660

Reviews:

Brands by name

Popular brands

APRILIA TUAREG 660, Service Station Manual

Search results

Summary of Contents for TUAREG 660

Reviews:

Brands by name

Popular brands