APRILIA TUAREG 660 Service Station Manual Download Page 272

Page: 272 / 311

•

Turn the handlebar all the way to the

left and remove the three fixing screws

(3) of the expansion tank.

•

Remove the expansion tank (4).

•

To refit the expansion tank, carry out the procedure described previously for removal in

reverse order.

•

After reconnecting all pipes and filling the system with the indicated quantity of coolant,

check that there are no leaks in the coupling points of the pipes.

See also

Capacities

Thermostatic valve

Removing

To remove the thermostatic valve, it is necessary

to previously drain the cooling system. Then pro-

ceed as described:

•

Remove the two cover fixing screws.

Cooling system

TUAREG 660

COOL SYS - 272

Summary of Contents for TUAREG 660
























































































































































































































































































































Search results

Summary of Contents for TUAREG 660

Reviews:

Brands by name

Popular brands

APRILIA TUAREG 660, Service Station Manual

Search results

Summary of Contents for TUAREG 660

Reviews:

Brands by name

Popular brands