manualshive.com logo in svg

APRILIA TUAREG 660, Service Station Manual

Share
Download
APRILIA TUAREG 660 Service Station Manual Download Page 132

•

After disconnecting the clutch cable

from the lever, unscrew the screw (13),

move the handlebar to the right and re-

move the clutch lever (14).

•

Remove the handlebars.

Front fork

Adjustment

The front suspension consists of a hydraulic fork

connected to the headstock by means of two

plates.

For the settings of the vehicle set-up:

•

Each stanchion has an upper nut (1) to

adjust the spring pre-load.

•

An upper adjuster screw (2) on the left

stanchion for setting the hydraulic

compression damping.

•

An upper adjuster screw (3) on the right

stanchion for setting the hydraulic re-

bound damping.

TO AVOID DAMAGE, DO NOT FORCE THE ADJUSTERS
BEYOND THE MAXIMUM SETTING POSITION IN EITHER
DIRECTION.
SET BOTH STANCHIONS WITH THE SAME SPRING PRE-
LOAD CALIBRATION.

Suspensions

TUAREG 660

SUSP - 132

Summary of Contents for TUAREG 660
























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands