APRILIA TUAREG 660 Service Station Manual Download Page 226

Page: 226 / 311

5. Front brake master cylinder

6. Rear brake pump

7. Front brake control lever

8. Rear brake pedal

9. Front brake circuit inlet solenoid valve (normally open)

10.Rear brake circuit inlet solenoid valve (normally open)

11.Front brake circuit outlet solenoid valve (normally closed)

12.Rear brake circuit outlet solenoid valve (normally closed)

13.Rear/front brake circuit low pressure accumulator

14.Dual hydraulic circuit pump (ABS)

15.Hydraulic circuit motor

16.DC electric motor

Inlets and outlets:

1. Supply to the rear brake calliper.

2. Intake from the rear brake pump.

3. Inlet from front brake master cylinder.

4. Outlet to front brake calliper.

ABS OPERATION

General specifications:

The front circuit is the same as the rear one.

•

The ABS inlet valve (9 - 10) is normally open and it is closed only when the system intervenes

to avoid wheel locking.

•

The exhaust valve (11 - 12) is normally closed and it is opened only when the system in-

tervenes to avoid wheel locking.

•

With the system in stand-by mode, the ABS processor controls the wheel speed instant by

instant to assess any slippage of the wheels.

•

When in standby, the system does not intervene at all when the rider brakes; the braking

system is the same as the one without ABS.

ABS Cycle phases (the following operations refer to the front circuit but they are also valid for

the rear):

A - Brake activation: the rider starts braking

as he would usually do.

B - Pressure reduction:

coincides with the recognition of the dangerous situation (wheel slippage

exceeds the threshold): the system closes the inlet valve (9-10) and opens the outlet valve (11-12)

temporarily.

Braking system

TUAREG 660

BRAK SYS - 226

Summary of Contents for TUAREG 660
























































































































































































































































































































Search results

Summary of Contents for TUAREG 660

Reviews:

Brands by name

Popular brands

APRILIA TUAREG 660, Service Station Manual

Search results

Summary of Contents for TUAREG 660

Reviews:

Brands by name

Popular brands