manualshive.com logo in svg

APRILIA TUAREG 660, Service Station Manual

Share
Download
APRILIA TUAREG 660 Service Station Manual Download Page 139

Sleeve

Check for damage and/or cracks; if it is damaged, replace it.

Springs

Check the condition of the springs, making sure that the length is within the acceptable limits.

If not, replace the springs.

MINIMUM LENGTH OF FREE SPRING: 454.2 mm (17.88 in)

Reassembling the fork

NOTE

THE FOLLOWING OPERATIONS REFER TO A SINGLE STANCHION BUT APPLY TO BOTH.

To reassemble the fork, proceed as follows:

•

Insert the dust guard (1), the seeger

ring (2), the oil seal (3), the ring (4), the

guide bushing (5) and the slider bush-

ing (6) on the stanchion.

•

Using the special protective jaws,

block the stanchion horizontally in a

vice.

•

Insert the complete damper rod (7) on

the stanchion.

•

Insert a new seal washer (8) on the fix-

ing screw (9) of the damper rod and

tighten it to torque.

TUAREG 660

Suspensions

SUSP - 139

Summary of Contents for TUAREG 660
























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands