APRILIA TUAREG 660 Service Station Manual Download Page 193

Page: 193 / 311

•

Position the 4 gaskets (4) on the swing-

arm to the level of the internal machin-

ing as shown in the image.

•

Working from both sides, insert the "T"

bush (5) complete with shoulder wash-

er (6).

•

Working from both sides, position the

flat washers (8) on the swingarm (7)

paying attention to the correct align-

ment. The machined part must be fac-

ing the swingarm.

•

Then insert the swingarm into its seat.

•

Working from the right side of the ve-

hicle, supporting the swingarm, insert

the swingarm pin (9) making sure that

it is inserted as far as it will go.

•

Position a rear stand to support the

swingarm

TUAREG 660

Chassis

CHAS - 193

Summary of Contents for TUAREG 660
























































































































































































































































































































Search results

Summary of Contents for TUAREG 660

Reviews:

Brands by name

Popular brands

APRILIA TUAREG 660, Service Station Manual

Search results

Summary of Contents for TUAREG 660

Reviews:

Brands by name

Popular brands