APRILIA SPORTCITY ONE 125 Service Station Manual Download Page 99

Page: 99 / 176

In case of anomalies, replace the damaged com-

ponents.

Characteristic

Minimum diameter permitted

Ø 11.970 mm

Maximum diameter admitted

Ø 12.030 mm

Refitting the head and timing system components

- Fit the timing chain guide pad.

- Insert the head and cylinder centring dowels, fit the head gasket and the head on the cylinder.

-Screw the nuts and lock them in a crossed sequence and in 2 or 3 stages to the specific torque.

Locking torques (N*m)

Locking torque

28 ÷ 30

- Fit the two screws on the outside of the timing

chain side and tighten them to the specified torque.

NOTE

BEFORE INSTALLING THE HEAD, MAKE SURE THAT THE
LUBRICATION CHANNEL IS CLEAN USING A COM-
PRESSED AIR JET.

Locking torques (N*m)

Locking torque

11 ÷ 13

- Fit the timing chain sprocket wheel on the crank-

shaft, with the chamfer facing the insertion side.

- Loop the timing chain around the sprocket on the

crankshaft.

- Fit the tensioner pad by the cylinder head.

- Fit the spacer and the screw fastener.

- Fit the pin, the outlet rocking lever, the spring

washer and the inlet rocking lever.

- Lubricate the 2 rocking levers through the holes

at the top.

- Lubricate the 2 bearings and insert the camshaft

in the cylinder head with the cams opposing the

rocking levers.

SPORTCITY ONE 125

Engine

ENG - 99

Summary of Contents for SPORTCITY ONE 125

















































































































































































Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands

APRILIA SPORTCITY ONE 125, Service Station Manual

Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands