APRILIA SPORTCITY ONE 125 Service Station Manual Download Page 34

Page: 34 / 176

IN ORDER TO AVOID DAMAGING THE ENGINE, OIL LEVEL
MUST NEVER EXCEED THE «MAX» MARK OR FALL BE-
LOW THE «MIN» MARK.

•

Top-up if required.

TOP-UP

Do not exceed the «

MAX

» mark level when topping-up engine oil.

•

Pour a small quantity of oil through the tube and wait about one minute so that the oil flows

evenly into the crankcase.

•

Check the oil level and top up, if required.

•

Top up with small quantities of oil, until the recommended level is reached.

•

Once this operation is finished, screw and tighten the cap-dipstick «1».

CAUTION

RIDING THE VEHICLE WITH INSUFFICIENT LUBRICATION OR CONTAMINATED OR NOT REC-
OMMENDED LUBRICANTS ACCELERATES THE WEAR AND TEAR OF MOVING PARTS AND
CAN CAUSE IRRETRIEVABLE DAMAGE.

Fuel filter

Cleaning the fuel filter

•

Empty the fuel tank.

•

Unscrew the clamp «1».

•

Remove the pipe «2».

•

Slide off the petrol flange «3».

•

Unscrew the filter «4» from the flange

«3».

NOTE

BLOW THE FILTER WITH COMPRESSED AIR AND REFIT.

Maintenance

SPORTCITY ONE 125

MAIN - 34

Summary of Contents for SPORTCITY ONE 125

















































































































































































Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands

APRILIA SPORTCITY ONE 125, Service Station Manual

Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands