manualshive.com logo in svg

APRILIA SPORTCITY ONE 125, Service Station Manual

Share
Download
APRILIA SPORTCITY ONE 125 Service Station Manual Download Page 154

•

Connect a transparent pipe to the

bleeder «2».

CAUTION

DO NOT DIRT THE PADS OR THE DISC WITH BRAKE FLU-
ID.

•

Keep the free part of the glass tube in

a clean container.

•

Pull the brake lever slowly «5» all along

its stroke two or three times, then keep

it pulled to the fullest.

CAUTION

LOOSEN THE BLEED PLUG SPOUT «2» AND CHECK THE
RESERVOIR BRAKE FLUID LEVEL «6». DO NOT EMPTY
THE RESERVOIR COMPLETELY SINCE THIS MAY FUR-
THER CAUSE AIR TO ENTER THE BRAKING SYSTEM.

•

Loosen the bleed plug spout «2» and check if there are bubbles in the glass tube.

CAUTION

BEFORE RELEASING THE BRAKE LEVER «5», CLOSE THE BLEED PLUG «2» TO PREVENT
WATER FROM ENTERING THE BRAKE SYSTEM.

•

When the brake fluid that comes out is homogeneous, without bubbles, it means air has

successfully been eliminated from the system. Close the bleed plug «2» accurately, and

tighten it correctly.

NOTE

REPEAT THE LAST TWO OPERATIONS UNTIL THE BUBBLES ARE TOTALLY ELIMINATED.

•

Refit the protection cap «1» on the bleed plug spout «2».

•

Check the brake fluid level.

CAUTION

AFTER REFITTING, PULL THE BRAKE LEVER REPEATEDLY AND CHECK THAT THE BRAKING
SYSTEM OPERATES CORRECTLY.

CAUTION

PAY ATTENTION TO THE DISC AND THE FRICTION MATERIAL MAKING SURE THEY ARE NOT
DIRTY OR GREASED, SPECIALLY AFTER MAINTENANCE OPERATIONS OR INSPECTION.

Braking system

SPORTCITY ONE 125

BRAK SYS - 154

Summary of Contents for SPORTCITY ONE 125

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands