APRILIA SPORTCITY ONE 125 Service Station Manual Download Page 133

Page: 133 / 176

Adjusting the idle

- The engine does not require frequent idle speed

adjustments, but it is essential to strictly follow cer-

tain rules when adjusting the idle speed.

- Before adjusting the carburettor make sure that

the lubrication requirements and valve clearance

are met, timing is respected, the spark plug is in

optimum conditions, the air filter is clean and

sealed, and the exhaust system is sealed.

- Warm up the engine letting it run at 50 Km/h for

at least 5 minutes.

- Connect the multimeter thermometer (020331y)

to the sump, using a cap with oil expressly pre-

pared for probes.

- Start the engine and before adjusting idle speed,

make sure that the oil temperature is between

70÷80 °C

- Using the rpm indicator or any other instrument

(020332y), adjust the idle screw to obtain 1600

rpm ÷ 1700 rpm.

NOTE

THE WASTED SPARK IGNITION SYSTEM OFFERS RE-
MARKABLE POWER. READINGS MAY NOT BE ACCU-
RATE IF INADEQUATE RPM INDICATORS ARE USED.
CORRECT COUPLING OF THE RPM INDICATOR WILL BE
INDICATED WHEN IT CAN ALSO READ RPM OVER 6000 ÷
8000

SPORTCITY ONE 125

Engine

ENG - 133

Summary of Contents for SPORTCITY ONE 125

















































































































































































Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands

APRILIA SPORTCITY ONE 125, Service Station Manual

Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands