manualshive.com logo in svg

APRILIA SPORTCITY ONE 125, Service Station Manual

Share
Download
APRILIA SPORTCITY ONE 125 Service Station Manual Download Page 106

Specific tooling

020074Y

 

Support base for checking crankshaft

alignment

Characteristic

Off-line maximum admitted

A

 = 0.15 mm

B

 = 0.01 mm

C

 = 0.01 mm

D

 = 0.10 mm

Inspecting the crankcase halves

- Before proceeding to check the crankcase

halves, thoroughly clean the all surfaces and oil

ducts.

- On the transmission side crankcase half, take

particular care cleaning the housing and oil ducts

for the following components: the oil pump, the oil

by-pass valve, the main bushings and the cooling

jet on the transmission side (see diagram).

- Take particular care, also, that there are no signs

wear in the oil by-pass valve housing (see Chapter

Lubrication), as this could prevent a good seal in

the valve, which regulates the oil pressure.

NOTE

THE JET IS FED THROUGH THE MAIN BUSHINGS. PROP-
ER OPERATION OF THIS COMPONENT IMPROVES THE
PISTON TOP COOLING. CLOGGING HAS EFFECTS THAT
ARE DIFFICULT TO DETECT (PISTON TEMPERATURE IN-
CREASE). FAILURE OR LEAK CAN CONSIDERABLY DE-
CREASE THE MAIN BUSHING AND CONNECTING ROD
LUBRICATION PRESSURE.

- On the flywheel side crankcase half, take partic-

ular care cleaning the oil ducts for the main bush-

ings, the oil duct for the jet that lubricates the

cylinder head and the oil drainage duct at the fly-

wheel side oil seal.

NOTE

THE HEAD LUBRICATION CHANNEL IS PROVIDED WITH
A SHUTTER JET; THIS GIVES A "LOW PRESSURE" HEAD
LUBRICATION; THIS CHOICE WAS MADE TO REDUCE
THE OIL TEMPERATURE IN THE SUMP. THE JET CLOG-
GING IMPAIRS THE HEAD LUBRICATION AND THE TIM-
ING MECHANISMS. A JET FAILURE CAUSES A DE-
CREASE OF THE MAIN BUSHING AND CONNECTING ROD
LUBRICATION PRESSURE.

Engine

SPORTCITY ONE 125

ENG - 106

Summary of Contents for SPORTCITY ONE 125

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands