APRILIA SPORTCITY ONE 125 Service Station Manual Download Page 124

Page: 124 / 176

Refitting the carburettor

- Before refitting, wash the carburettor body accu-

rately with petrol and compressed air.

- Pay special attention to the fuel supply pipe and

the plunger seat.

- For maximum circuit, check the air adjustment is

correct as shown in the figure.

- For the minimum circuit, make sure the following

points are properly cleaned: air gauging, outlet

section controlled by flow screw, progression

holes near the throttle valve.

- For the starter circuit, blow the connection pipe properly with the jet. This is necessary because the

nozzle support hides other inaccessible internal calibrations.

- Blow the intake nozzle properly.

NOTE

THE ACCELERATION NOZZLE OUTLET IS EXTREMELY SMALL AND IS ORIENTED TO THE
THROTTLE VALVE. NOZZLE INCORRECT ORIENTATION RESULTS IN INADEQUATE SPRAY-
ING.

- Check that there are 5 closing ball joints for the operating pipes on the carburettor body.

Engine

SPORTCITY ONE 125

ENG - 124

Summary of Contents for SPORTCITY ONE 125

















































































































































































Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands

APRILIA SPORTCITY ONE 125, Service Station Manual

Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands