APRILIA SPORTCITY ONE 125 Service Station Manual Download Page 116

Page: 116 / 176

Measure the distance between the outer rotor and

the pump body; see figure.

Characteristic

Admissible limit clearance:

0.20 mm

Check the axial clearance of the rotors with a trued

bar as reference, as shown in the figure.

Characteristic

Limit values admitted:

0.09 mm

Refitting

- Check there are no signs of wear on the oil pump

shaft or body.

- Check there are no signs of scoring or wear on

the oil pump cover.

- If you detect non-conforming measurements or

scoring, replace the faulty parts or the assembly.

- Fit the pulley to the pump, the central screw to

the specified torque and the belleville washer.

-Fit the oil pump cover, by tightening the two

screws to the prescribed torque.

NOTE

FIT THE BELLEVILLE WASHER SO THAT ITS OUTER
(CURVED) RIM TOUCHES THE PULLEY.

Locking torques (N*m)

Central screw

12 ÷ 14 Nm

Cover screws

0.7 ÷ 0.9 Nm

Engine

SPORTCITY ONE 125

ENG - 116

Summary of Contents for SPORTCITY ONE 125

















































































































































































Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands

APRILIA SPORTCITY ONE 125, Service Station Manual

Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands