APRILIA SPORTCITY ONE 125 Service Station Manual Download Page 89

Page: 89 / 176

Rod small end check-up: Standard diameter

15 +0.015+0.025 mm

Inspecting the wrist pin

- Check the outer diameter of the gudgeon pin.

Characteristic

Standard pin diameter

14.996 ÷ 15 mm

Minimum diameter permitted

Ø 14.994 mm

- Calculate the piston pin coupling clearance.

NOTE

THE PIN HOUSINGS HAVE 2 LUBRICATION CHANNELS.
FOR THIS REASON MEASUREMENT OF THE DIAMETER
MUST BE CARRIED OUT ACCORDING TO THE AXIS OF
THE PISTON.

Characteristic

Piston pin bore - standard diameter

Ø 15+0.001 +0.006

- Measure the outside diameter of the piston, per-

pendicular to the gudgeon pin axis.

- Measure 36.5 mm from the piston crown's shown

in the figure.

NOTE

THE PIN HOUSINGS HAVE 2 LUBRICATION CHANNELS.
FOR THIS REASON MEASUREMENT OF THE DIAMETER
MUST BE CARRIED OUT ACCORDING TO THE AXIS OF
THE PISTON.

- Using a bore meter, measure the inner cylinder

diameter at three different points according to the

directions shown in the figure.

- Check that the coupling surface with the head is

not worn or misshapen.

- Pistons and cylinders are classified into catego-

ries based on their diameter. The coupling is car-

ried out in pairs (A-A, B-B, C-C, D-D).

Characteristic

SPORTCITY ONE 125

Engine

ENG - 89

Summary of Contents for SPORTCITY ONE 125

















































































































































































Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands

APRILIA SPORTCITY ONE 125, Service Station Manual

Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands