APRILIA SPORTCITY ONE 125 Service Station Manual Download Page 87

Page: 87 / 176

- Remove the pin of the rocking levers from the

flywheel side holes.

- Remove the rocking levers and the elastic wash-

er.

NOTE

MARK THE ROCKING LEVERS ASSEMBLE POSITION, SO
AS TO AVOID THE INVERSION OF INLET WITH THE OUT-
LET.

Removing the cylinder head

- Remove the spark plug.

- Remove the 2 side fixings shown in the figure.

- Loosen the 4 head-cylinder fastening nuts in two

or three stages and in criss-cross fashion.

- Remove the head, the two centring dowels and

the gasket.

NOTE

IN CASE OF NEED, THE HEAD MAY BE REMOVED WITH
THE CAMSHAFT, PINS, ROCKING LEVERS AND FIXING
BRACKET. THE HEAD CAN ALSO BE REMOVED WITH-
OUT REMOVING THE CHAIN AND THE DRIVING SHAFT
CHAIN TIGHTENER.

Removing the valves

- Using the specific tool fitted with the element

shown in the figure, remove the cotters, the plates

and the spring between the valves.

Specific tooling

020382Y

Tool for removing valve cotters fitted

with part 012

020382Y011

adapter for valve removal tool

SPORTCITY ONE 125

Engine

ENG - 87

Summary of Contents for SPORTCITY ONE 125

















































































































































































Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands

APRILIA SPORTCITY ONE 125, Service Station Manual

Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands