APRILIA SPORTCITY ONE 125 Service Station Manual Download Page 109

Page: 109 / 176

- Fit the oil filter joint and tighten it to the prescribed

torque.

- Place a new gasket on one of the crankcase

halves, preferably on the transmission side, to-

gether with the locating dowels.

Locking torques (N*m)

Locking torque

27 ÷ 33

- Lubricate the main bushings and insert the crank-

shaft in the transmission side crankcase half.

- Reassemble the two crankcase halves.

- Fit the 11 screws and tighten them to the pre-

scribed torque.

NOTE

WHEN FITTING THE HALF CASING AND THE CRANK-
SHAFT, TAKE CARE NO TO DAMAGE THE SHAFT THREA-
DED TANGS.

Locking torques (N*m)

Locking torque

11 ÷ 13

- Lubricate the flywheel oil seal.

- Use the appropriate tool to assemble the oil seal.

- Fit a new O-ring on the pre-filter and lubricate it.

- Insert the pre-filter on the engine with its corre-

sponding cover to the specific torque.

NOTE

REMOVE ANY EXCESS FROM THE CRANKCASE COU-
PLING GASKET ON THE CYLINDER PLANE, TO ENSURE
BETTER SEALING PERFORMANCE.

NOTE

FAILURE TO USE THE SPECIFIC TOOL CAN RESULT IN
AN INCORRECT DEPTH POSITION AND AS A CONSE-
QUENCE IN INADEQUATE OIL SEALING.

Specific tooling

020425Y

Punch for flywheel-side oil seal

Locking torques (N*m)

Locking torque

24 ÷ 30

Lubrication

SPORTCITY ONE 125

Engine

ENG - 109

Summary of Contents for SPORTCITY ONE 125

















































































































































































Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands

APRILIA SPORTCITY ONE 125, Service Station Manual

Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands