APRILIA SPORTCITY ONE 125 Service Station Manual Download Page 147

Page: 147 / 176

•

Unscrew nut «2» fixing the shock ab-

sorber to the engine.

•

Follow the removal operations in reverse order for the fitting, screwing the nuts to the pre-

scribed torque.

Locking torques (N*m)

Upper part of the shock absorber retaining nut

22.5

Lower part of the shock absorber retaining

nut

42.5

Centre-stand

•

Rest the vehicle on its centre stand.

•

Place a support under the vehicle so that it does not fall after the centre stand is removed.

CAUTION

MAKE SURE THE SCOOTER IS STABLE AND FIRM. IF IT FALLS, IT MAY INJURY YOU OR OTHER
PEOPLE, DAMAGE THE VEHICLE ITSELF OR ANY ADJACENT OBJECTS.

•

Remove the two springs «1».

SPORTCITY ONE 125

Suspensions

SUSP - 147

Summary of Contents for SPORTCITY ONE 125

















































































































































































Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands

APRILIA SPORTCITY ONE 125, Service Station Manual

Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands