manualshive.com logo in svg

APRILIA SPORTCITY ONE 125, Service Station Manual

Share
Download
APRILIA SPORTCITY ONE 125 Service Station Manual Download Page 135

Front

Removing the front wheel

CAUTION

WHEN REMOVING OR REFITTING THE WHEEL, PAY SPECIAL ATTENTION NOT TO DAMAGE
THE BRAKE CABLE, THE DISCS AND THE PADS. BEFORE CARRYING OUT THE FOLLOWING
OPERATIONS, COOL DOWN THE ENGINE AND THE MUFFLER TO AMBIENT TEMPERATURE
TO AVOID POSSIBLE BURNS.

•

Rest the vehicle on its centre stand.

•

Place a support under the vehicle so that the wheel can move freely and the vehicle does

not fall.

CAUTION

MAKE SURE THE SCOOTER IS STABLE AND FIRM. IF IT FALLS, IT MAY INJURY YOU OR OTHER
PEOPLE, DAMAGE THE VEHICLE ITSELF OR ANY ADJACENT OBJECTS.

•

Loosen the two locking screws of the

wheel axle «1».

•

Loosen the wheel axle fixing screw

«2».

•

Slide off the axle and remove the

wheel.

CAUTION

NEVER TOUCH THE FRONT BRAKE LEVER ONCE THE
FRONT WHEEL IS REMOVED. DOING SO MAY CAUSE THE
CALLIPER PLUNGERS TO COME OUT AND THE BRAKE
FLUID TO SEEP THROUGH.

SPORTCITY ONE 125

Suspensions

SUSP - 135

Summary of Contents for SPORTCITY ONE 125

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands