manualshive.com logo in svg

APRILIA SPORTCITY ONE 125, Service Station Manual

Share
Download
APRILIA SPORTCITY ONE 125 Service Station Manual Download Page 64

Automatic transmission

Transmission cover

- To remove the transmission cover it is necessary

to remove the rear plastic cover first by inserting a

screwdriver in the corresponding slotted holes.

Using the clutch bell lock wrench, remove the driv-

en pulley axle locking nut and recover the washer.

- Remove the cap/dipstick from the engine oil filling

hole.

- Remove the 10 screws and the earth cable fas-

tened under one of them.

- Remove the transmission cover. If this operation

is performed directly on the vehicle, it is necessary

to remove the cooling air coupling and the three air

filter housing retainers.

Specific tooling

020423Y

 

Driven pulley lock wrench

Air duct

- Unscrew the Torx screws fixing the air manifold

bulkhead and remove the bulkhead.

- Remove the 3 screws, then take out the manifold

as well as the filter.

Engine

SPORTCITY ONE 125

ENG - 64

Summary of Contents for SPORTCITY ONE 125

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands