manualshive.com logo in svg

APRILIA SPORTCITY ONE 125, Service Station Manual

Share
Download
APRILIA SPORTCITY ONE 125 Service Station Manual Download Page 102

Locking torques (N*m)

Locking torque

 

3 ÷ 4

- Fit the inlet manifold and lock the 2 screws to the

specified torque.

- Fit the carburettor onto the inlet manifold and lock

the clamp

NOTE

FIT THE CARBURETTOR THROUGH THE SUPPLEMENT
ON THE MANIFOLD.

Locking torques (N*m)

Locking torque

 

11 ÷ 13

- Refit the cylinder head cover, tightening the 4

clamping screws to the prescribed torque.

- Refit the fan and the housing.

- Reassemble the oil pump control, the chain com-

partment cover, the by-pass and the oil sump as

described in the lubrication chapter.

- Reassemble the driving pulley, the belt and the

transmission cover as described in the transmis-

sion chapter.

Locking torques (N*m)

Locking torque

 

11 ÷ 13

Crankcase - crankshaft

- Precautionary remove the following units:

transmission cover, driving pulley, driven pulley

and belt, rear hub cover, gears, bearings and oil

seals as described in the transmission chapter.

- Remove the oil sump, the by-pass, the chain

compartment cover and the oil pump as in the lu-

brication chapter.

- Remove the flywheel cover, the fan, the flywheel

and the stator as described in the magneto fly-

wheel chapter.

- Remove the oil filter and the oil pressure bulb.

- Remove the cylinder-piston-head unit as descri-

bed in the cylinder head timing system chapter.

Engine

SPORTCITY ONE 125

ENG - 102

Summary of Contents for SPORTCITY ONE 125

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands