APRILIA SPORTCITY ONE 125 Service Station Manual Download Page 138

Page: 138 / 176

•

Apply a thin layer of lubricating grease

inside the speedometer transmission,

in the external seats of the wheel hub

and on the wheel axle.

•

Place the speedometer transmission

on the front wheel

•

Place the wheel between the fork rods

by inserting correctly the odometer

transmission in the housing on the fork

rod.

•

Insert the fork shaft and screw the nut

«1» to the prescribed torque.

Locking torques (N*m)

Wheel pin to fork fixing nut

46.5

•

Tighten the two locking «2» screws of

the wheel axle.

Locking torques (N*m)

Wheel pin hub fixing screw

Handlebar

Removal

NOTE

Suspensions

SPORTCITY ONE 125

SUSP - 138

Summary of Contents for SPORTCITY ONE 125

















































































































































































Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands

APRILIA SPORTCITY ONE 125, Service Station Manual

Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands