APRILIA SPORTCITY ONE 125 Service Station Manual Download Page 101

Page: 101 / 176

- Fit the automatic valve-lifter retaining dish, using

the counterweight screw fastener as a reference.

- Tighten the clamping screw to the prescribed tor-

que.

Locking torques (N*m)

Locking torque

12 - 14

- Set the tensioner cursor in the rest position.

- Fit the chain tensioner on the cylinder, using a new gasket, and tight the two screws to the prescribed

torque.

Locking torques (N*m)

Locking torque

11 ÷ 13

- Insert the chain tensioning screw, together with the spring and washer, tightening it to the prescribed

torque.

Locking torques (N*m)

Locking torque

5 - 6

- Adjust the valve clearance.

- Fit the spark plug

Characteristic

Spark plug

Champion RG6YC

Electric characteristic

Electrode gap

0.8 mm

Locking torques (N*m)

Locking torque

12 - 14

- Assemble the casing sealing gasket on the head.

On the fitting direction, use the supplements on the

timing side as reference.

- Assemble the screw fixing the housing to the

crankcase to the specified torque and the 2 self-

threading screws joining the half-shells.

- Take care that the gasket is well inserted in its

housing during the assembly stage.

- Place the spark plug access cap.

SPORTCITY ONE 125

Engine

ENG - 101

Summary of Contents for SPORTCITY ONE 125

















































































































































































Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands

APRILIA SPORTCITY ONE 125, Service Station Manual

Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands