APRILIA SPORTCITY ONE 125 Service Station Manual Download Page 95

Page: 95 / 176

Characteristic

Standard drainage guide diameter

5.012 mm

Standard inlet guide diameter

5.012 mm

- If the width of the impression on the valve seat or

the diameter of the valve guide exceed the speci-

fied limits, replace the cylinder head.

- Check width of the impression on the valve seat

Characteristic

Wear limits:

Max. 1.6 mm.

Inspecting the valves

- Measure the diameter of the valve stems in the

three positions indicated in the diagram.

- Calculate the clearance between valve and valve

guide.

Characteristic

Minimum diameter admitted - Inlet:

4.96 mm

Minimum diameter admitted - Outlet:

4.95 mm

Standard clearance - Inlet:

0.013 ÷ 0.040 mm

Standard clearance - Outlet:

0.025 ÷ 0.052 mm

Maximum clearance admitted- Inlet:

0.062 mm

Maximum clearance admitted - Outlet:

0.072 mm

SPORTCITY ONE 125

Engine

ENG - 95

Summary of Contents for SPORTCITY ONE 125

















































































































































































Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands

APRILIA SPORTCITY ONE 125, Service Station Manual

Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands