manualshive.com logo in svg

APRILIA SPORTCITY ONE 125, Service Station Manual

Share
Download
APRILIA SPORTCITY ONE 125 Service Station Manual Download Page 137

001467Y009

 

Bell for 42 mm outside diameter bearings

001467Y014

 

Pliers to extract Ø15 mm bearings

020357Y

 

32 x 35 mm adaptor

020376Y

 

Adapter handle

020412Y

 

15 mm guide

020456Y

 

Ø24 mm adaptor

WHEEL RIM INSPECTION

•

Make sure that the rim is not deformed

or cracked. Replace it if necessary.

•

Check wheel eccentricity. If tolerance

limits are exceeded, check the rim and

the bearings. If necessary, replace the

wheel.

Characteristic

Eccentricity limits:

Vertical: 2 mm (0.07874 in)

Horizontal: 2 mm (0.07874 in)

•

Check the wheel balance.

•

Check wheel on the wheel balancer and turn it several times, paying attention to its position

when it stops. If the wheel is steadily balanced, it will not always stop at the same point. If

it always stops at the same point, the wheel is not balanced and must be balanced. Place

weights on the lightest part of the wheel so that it does not stop any more at a particular

point after being turned several times.

Refitting the front wheel

CAUTION

WHEN REMOVING OR REFITTING THE WHEEL, PAY SPECIAL ATTENTION NOT TO DAMAGE
THE BRAKE CABLE, THE DISCS AND THE PADS. BEFORE CARRYING OUT THE FOLLOWING
OPERATIONS, COOL DOWN THE ENGINE AND THE MUFFLER TO AMBIENT TEMPERATURE
TO AVOID POSSIBLE BURNS.

SPORTCITY ONE 125

Suspensions

SUSP - 137

Summary of Contents for SPORTCITY ONE 125

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands