APRILIA SPORTCITY ONE 125 Service Station Manual Download Page 74

Page: 74 / 176

Removing the driving pulley

- Lock the driving pulley with the specific tool as

shown in the figure. - Disassemble the central nut

and the Belleville washer, remove the drive and

the 2 washers. - Remove the stationary half pulley

and the steel washer.

Specific tooling

020368Y

driving pulley lock wrench

- Remove the belt and slide the movable half-pul-

ley with the relevant bush, taking care of the falling

free assembled rollers.

- Remove the return rollers plate with the relative

guide pads.

Inspecting the rollers case

- Check that the internal bushing is not abnormally worn and measure inner diameter.

NOTE

DO NOT LUBRICATE OR CLEAN THE BUSHING.

BUSHING ROLLER CONTAINER

Specification

Desc./Quantity

Maximum allowable diameter

Ø 26.121 mm

Standard diameter

Ø 26+0 +0.021 mm

BUSH SLIDE PULLEY

Specification

Desc./Quantity

Minimum diameter permitted

Ø 25.950 mm

Standard diameter

Ø 26-0.020 -0.041 mm

VARIABLE SPEED ROLLERS

Specification

Desc./Quantity

Minimum diameter permitted

Ø 18.5 mm

Standard diameter

Ø 26±0.1 mm

Engine

SPORTCITY ONE 125

ENG - 74

Summary of Contents for SPORTCITY ONE 125

















































































































































































Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands

APRILIA SPORTCITY ONE 125, Service Station Manual

Search results

Summary of Contents for SPORTCITY ONE 125

Reviews:

Brands by name

Popular brands