manualshive.com logo in svg

APRILIA SPORTCITY ONE 125, Service Station Manual

Share
Download
APRILIA SPORTCITY ONE 125 Service Station Manual Download Page 130

- Wash and blow dry the starter support.

Assemble a new gasket on the carburettor body and tighten the 2 fixing screws.

Inspecting the automatic choke device

- Check that the automatic starter piston is not deformed or rusty.

- Check that the piston slides freely from the seat to the support.

- Check that the piston sealing gasket is not deformed.

- The starter must be more or less functional depending on the ambient temperature.

- Measure the protrusion of the piston as shown in the figure and check its corresponding value.

- Make sure that the starter is adjusted for the ambient temperature.

- The starter should disconnect progressively by means of electric heating.

- Check the starter resistance when adjusted to the ambient temperature.

With a 12V battery power the automatic starter and check that the piston protrudes as much as possible.

Engine

SPORTCITY ONE 125

ENG - 130

Summary of Contents for SPORTCITY ONE 125

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands