Applied Biosystems GeneAmp PCR System 9700 User Manual Download Page 47

Page: 47 / 132

Instrument Setup 3-19

Upgrading the System Firmware

Introduction

You can update the GeneAmp PCR System 9700 firmware from a serial connection to
the RS485 port or from a PCMCIA Flash Memory Card.

Contact your local Applied Biosystems representative to obtain a PCMCIA Flash
Memory Card.

Upgrading Through

the Serial Port

The following procedure describes how to upgrade the firmware through the RS485
serial port.

To upgrade the firmware through the RS485 serial port:

Step

Action

Connect the appropriate communication cable from a computer to the RS485 port
on the 9700 instrument Base Module (see the figure below).

You can use the following cables:

For information on connecting the printer cable, see page 3-27.

From the

Diagnostics

screen, press

Upgrade

The Firmware Upgrade screen appears.

Communication cable

Part number

PC communication cable

N805-1327

Macintosh communication cable

N805-1328

GR0877

RS485

Ports

Firmware Upgrade

PCcard - Upgrade from PC card
Serial - Upgrade from serial port

Exit

Serial

PCcard

Summary of Contents for GeneAmp PCR System 9700





































































































































Search results

Summary of Contents for GeneAmp PCR System 9700

Reviews:

Related manuals for GeneAmp PCR System 9700

Brands by name

Popular brands

Applied Biosystems GeneAmp PCR System 9700, User Manual

Search results

Summary of Contents for GeneAmp PCR System 9700

Reviews:

Related manuals for GeneAmp PCR System 9700

Brands by name

Popular brands