Applied Biosystems GeneAmp PCR System 9700 User Manual Download Page 109

Page: 109 / 132

Instrument Specifications A-3

Control Panel Specifications

Display Screen

The display screen is a 7 x 40 character display with a graphics mode of 60 x 240 pixel
resolution.

Keys

The instrument control panel consists of a display screen and 22 keys. The keys are:

♦

Function keys

♦

Arrow keys

♦

Stop key

♦

Enter key

♦

10 number keypad

Sample Temperature Information

Temperature

The following table lists sample temperature information.

Note

Sample temperatures are displayed in degrees Celsius to the nearest 0.1 °C.

Printer Specifications

Serial Interface

Board Specifications

The instrument can use any printer with a serial (RS-232C) interface board with the
following parameters.

Cable Part Number

Connect the printer to the Instrument port with printer cable part number N805-1326.

Sample Temperature Range

4.0 to 99.9 °C.

Temperature Calibration

Traceable to National Institute of Standards and
Technology (NIST).

Baud Rate

9600

Parity

NONE

Data Bits

Stop Bits

Summary of Contents for GeneAmp PCR System 9700





































































































































Search results

Summary of Contents for GeneAmp PCR System 9700

Reviews:

Related manuals for GeneAmp PCR System 9700

Brands by name

Popular brands

Applied Biosystems GeneAmp PCR System 9700, User Manual

Search results

Summary of Contents for GeneAmp PCR System 9700

Reviews:

Related manuals for GeneAmp PCR System 9700

Brands by name

Popular brands