manualshive.com logo in svg

Applied Biosystems GeneAmp PCR System 9700, User Manual

The Applied Biosystems GeneAmp PCR System 9700 is a high-performance tool for DNA amplification. Unlocking its full potential is made easy with the free user manual available for download on our website. Experience seamless PCR processes and precision-driven results with the help of this comprehensive manual.

Share
Download
background image

Instrument Setup 3-27

Connecting and Configuring a Printer

Connecting a Printer

If you connect an optional printer to your 9700 instrument, you can print out a hard 
copy of the time and temperature parameters for the PCR methods you create.

Connect one end of your printer cable (N805-1326) to the RS-485 serial port on the 
side panel of the 9700 instrument and connect the other end to the RS-232C interface 
serial adapter on the rear panel of the printer.

Configuring the

Printer

After you have connected the printer cable to the printer, you must configure the 
instrument for the printer. You can connect the 9700 instrument to any printer with a 
serial board and the following specifications:

See your printer manual for instructions on how to complete any other necessary 
installation steps.

Baud Rate

9600

Parity

NONE

Data Bits

8

Stop Bits

1

Summary of Contents for GeneAmp PCR System 9700





































































































































Reviews:

No comments

Related manuals for GeneAmp PCR System 9700

Lawler 410 Installation & Maintenance Manual preview
410
Brand: Lawler Pages: 4
jbc DDE-1B Manual preview
DDE-1B
Brand: jbc Pages: 44
jbc SKR Instruction Manual preview
SKR
Brand: jbc Pages: 8
Kärcher K 3 How To Connect preview
K 3
Brand: Kärcher Pages: 4
NAPCO MFA6000 Operating & Installation Instructions Manual preview
MFA6000
Brand: NAPCO Pages: 48
NAPCO Magnum Alert 2600 Operating & Installation Instructions Manual preview
Magnum Alert 2600
Brand: NAPCO Pages: 68
Vacon 100X series Installation, Technical And Maintenance Manual preview
100X series
Brand: Vacon Pages: 132
OJ Electronics OJ-Air2-WP55 Instructions Manual preview
OJ-Air2-WP55
Brand: OJ Electronics Pages: 8
Finnleo SaunaLogic SL2 Control Manual preview
SaunaLogic SL2 Control
Brand: Finnleo Pages: 14
Grosvenor RM-LUM-M320-IT/A Installation Manual preview
RM-LUM-M320-IT/A
Brand: Grosvenor Pages: 2
micro-trak Calc-An-Acre II Reference Manual preview
Calc-An-Acre II
Brand: micro-trak Pages: 30
IFM Ecomat100 CR1055 Mounting And Installation Instructions Manual preview
Ecomat100 CR1055
Brand: IFM Pages: 32
schmersal AES 1175 Operating Instructions Manual preview
AES 1175
Brand: schmersal Pages: 6
D+H RZN 43 Series Original Instructions preview
RZN 43 Series
Brand: D+H Pages: 2
GRAUPNER MC-22S Programming Manual preview
MC-22S
Brand: GRAUPNER Pages: 180
FMS 109753-KIM Manual preview
109753-KIM
Brand: FMS Pages: 108
Ublox SARA-R42 Development Manual preview
SARA-R42
Brand: Ublox Pages: 58
Ravel RE -102 Installation, Commissioning & Operating Manual preview
RE -102
Brand: Ravel Pages: 33

Brands by name

Popular brands

Load more brands