Applied Biosystems GeneAmp PCR System 9700 User Manual Download Page 33

Page: 33 / 132

Instrument Setup 3-5

Converting from a Single to Double-Line Fuse

Introduction

FIRE HAZARD. For continued protection against the risk of fire, replace fuses

only with listed and certified fuses of the same type and rating as those currently in the
instrument.

This procedure describes how to convert the instrument from the single-line
configuration to double-line service (220/230/240 V nominals only).

IMPORTANT

For proper operation, you must know the power source(s) available and

determine if the instrument fuse configuration is correct. The instrument is shipped configured
for single-line operation.

Fuse Part Number

The correct fuse is an 8 amp Type T 250 V 5x20 mm fuse, P/N 0999-1683

Power Entry Module

Diagram

The following is a diagram of the Power Entry Module.

WARNING

GR0961

Jumper clip

Fuse compartment

Compartment door

Fuse

GR0878

One fuse
already installed

Summary of Contents for GeneAmp PCR System 9700





































































































































Search results

Summary of Contents for GeneAmp PCR System 9700

Reviews:

Related manuals for GeneAmp PCR System 9700

Brands by name

Popular brands

Applied Biosystems GeneAmp PCR System 9700, User Manual

Search results

Summary of Contents for GeneAmp PCR System 9700

Reviews:

Related manuals for GeneAmp PCR System 9700

Brands by name

Popular brands