Applied Biosystems GeneAmp PCR System 9700 User Manual Download Page 44

Page: 44 / 132

3-16 Instrument Setup

Testing the Display

Screen

The Display diagnostic test allows you to visually determine if the display screen is
properly functioning by turning on and off all the LCD pixels.

To test the display screen:

Step

Action

From the

Hardware Diagnostics

screen, press

Display

The Display Diagnostic screen appears.

You can take the following action:

Display Diagnostics

1. Read all instructions first.
2. Press Run to turn ON all pixels.
3. Press STOP to turn OFF all pixels.
4. Press STOP to exit.

Run

Exit

Press...

To...

Run

Turn ON all pixels.

Check display.

Stop

Turn OFF all pixels.

Check display.

Stop, again

Exit.

Summary of Contents for GeneAmp PCR System 9700





































































































































Search results

Summary of Contents for GeneAmp PCR System 9700

Reviews:

Related manuals for GeneAmp PCR System 9700

Brands by name

Popular brands

Applied Biosystems GeneAmp PCR System 9700, User Manual

Search results

Summary of Contents for GeneAmp PCR System 9700

Reviews:

Related manuals for GeneAmp PCR System 9700

Brands by name

Popular brands