Applied Biosystems GeneAmp PCR System 9700 User Manual Download Page 48

Page: 48 / 132

3-20 Instrument Setup

From the

Firmware Upgrade

screen, press

Serial

IMPORTANT

Do not remove the cable or turn off the instrument until the upgrade

is completed.

From the

Serial Port Firmware Upgrade

screen, press

Update

Take the following action:

To upgrade the firmware through the RS485 serial port:

(continued)

Step

Action

Serial Port Firmware Upgrade

Exit

Update

Attach cable from RS485 port on 9700 to
serial port on computer. Press Update,
then begin download of file from the
computer.

DO NOT TURN OFF THE INSTRUMENT

OR REMOVE SERIAL CABLE!

Upgrading over the serial port

will take approximately 10 minutes.

Instrument will re-boot when complete.

If you are using...

See...

Microsoft

™

Windows

95, or Microsoft
Windows NT

“Downloading Firmware Using Windows 95 or
Windows NT” on page 3-21.

Microsoft Windows

3.1

“Downloading Firmware Using Windows 3.1” on
page 3-22.

Summary of Contents for GeneAmp PCR System 9700





































































































































Search results

Summary of Contents for GeneAmp PCR System 9700

Reviews:

Related manuals for GeneAmp PCR System 9700

Brands by name

Popular brands

Applied Biosystems GeneAmp PCR System 9700, User Manual

Search results

Summary of Contents for GeneAmp PCR System 9700

Reviews:

Related manuals for GeneAmp PCR System 9700

Brands by name

Popular brands